Видео

How come mine hasn't got the gyro setting in menu

Hi Ron, great series of videos and very helpful during my first set up of a Beast FBL unit. I too have a YT channel and was going to make a set up video but why invent the wheal. Are you OK if I had a link on my video to your series? Many thanks Pete

I wonder who benefits from this...not beginners..and people who already know this stuff don't need to see it.. hmmm

never used one check by eye then hover and adjust trims shorten rods as required after flight been doing this for 30 years ,works for me no faffing about

just got my hands on one. did not know they existed. appreciate the research and quality

Thanks I purchased a T-Rex 500 electric used the original yellow one I've flown it a few times after fixing it up this will definitely help me fine tune it😊👍

Thanks Ron, video is a little old now but still relevant!! I'm using a Spektrum NX series tx now but assume the process is the same? Wiring my new Align TB40 now and am getting ready to set up and initialize. This video was great!

Hello Ron, Is it posible to connect the yellow ESC conector to be used as a Governor, using a standard futaba receptor?

Hi Ron missed you I am 71

How to binding the 3GX with flysky transmeter

You know you don't have to read them we can see on the screen

Hello, is there a setup for the jr remote control?

It was never mentioned here but you can run a higher gain value with a smaller arm on your servo. This may work better for you so experiment with the overall length of the arm or the position of the ball on the arm.

That's a sad thing to see the hobby is dying with out hobby shop s in the last 8 years I have seen 3 hoody shops close we have one left & I have a feeling it's not good to be around much longer mady 5 to 10 years & it will be gone 😢😢so sad

Hello. Do you have a video on aligning flybar blades and swash plate?

You never said which way round the 3 wires go into the rx

Thank you.

You want the leading edge to move against the way the tail is moving. If the tail is moving right the leading edge moves left and Vice versa to correct the tail.

Thank you much.

Hi Ron. I have the same problem at 3:35, imbalance in the tail of the helicopter. Please Help

Thank you. Calmly explained

The voice is just too annoying, i do not want to watch this

Awesome easy to understand thank you

Dose this work good for a blade msr,thanks

Ron- Your video's are excellant. I am using the Microbeast on a Align Super Dominator 470LP__ I have been flying it for several months now. All my settings seem to be ok. I have yet to run into someone who can advise me on -when swash is all the way negative & I cycle servos they bind up with bottom of servo/frame-they make contact because overextending? I have bound to DX9. I'm no where near the level to go full neg. & spin yet so it's not a problem yet. It can't be good for servos though. I suppose the Micro Beast would be where I would adjust it to stop before binding but not losing the throw?---Bob

Hello. If the flybar is located above the main blades of the helicopter, can this design also be used?

i have the dx8 gen 1, i was led to believe this had forward programming ect. However it doesnt, how can i make use of the as3x and safe feauture inside the rx AR637T ??

Qual é essa câmera amigo

Nice

VOICE SUCKS ,.................... BIG TIME

2022 thanks Ron Lund

RON! This setup works! I've watched this video over & over... I have much more knowledge & confidence in my nitro & electric heli setups! Thank you!

lppoplpp000p9pol 'll

hi what is the cable your using to plug in the receiver great vid thanks

Can I use FS-i6X transmitter and receiver ?

Thanks for all your help. Much respect. Rest in peace.

Hello Ron. I am trying to set MB plus V5 Governor Menu D on a nitro heli. I am using Open TX (TX16S). I couldn’t get the Manual control(LIGHTS OFF) using the flight mode switch. Idle up and autorotation lights are ok oer the manual. Can u advise what could be wrong?

Miss you Ron, hope your enjoying retirement!

I remember ordering from them. provided great services. His voice is epic.

Good day Ron. I just got a 360cfx from a friend who got tired fixing. When i spool up it turns to one side. When I counter it once it starts to turn that side. So its like the tail slider is sticking to the last input. Please help me troubleshoot. Thanks!

Hi sir, my trex550 titled to the right during launch of the throttle, was it due to the balancing of the wash plate?

How does Futaba T12ZA shut down the launch? When my Receiver R6208SB wants to link the frequency, T12ZA should be set in that project

How does Futaba T12ZA shut down the launch? When my Receiver R6208SB wants to link the frequency, T12ZA should be set in that project

Great 🙏🏻

What usefull you teach like this video? do'nt download it

Ron I got major probleagm. Maybe you can help me. I understand that tail is supposed to move in the opposite direction When acted on. Well that's not the case with me. FOR EXAMPLE: When I move the tail left the leading edge of the blade goes left too instead of right. Now obviously you'd be right to think you have to go in microbeastx gyro setup F and reverse gyro direction. Right? Well in my case it don't work. Ron what do I do old buddy? I am stumped. It's a brand new Microbeastx never crashed or broke?

Thanks so much Ron. Your videos are great and I appreciate the thought of safety. Which I did follow your advice on a video and set it up.

What can I say Ron, we all miss you buddy.

RIP, Ron.